Free, private, ready to print

Lithophane Maker

Turn a photo into a 3D printable lithophane: a thin panel that shows the picture when light shines through it.

Last updated: November 2026

Lit

Preview

3D

Preview

STL

Watertight

Private

No uploads

Drop your photo here

JPG, PNG, HEIC, WebP and more. Portraits and pets with clear light and shadow make the best lithophanes.

Your photo never leaves this device

How to make a lithophane

01

Add your photo

Drop or choose a JPG, PNG, HEIC or other photo. It opens on your device.

02

Set the size and thickness

Type the width in millimeters, and the thinnest and thickest points. The height follows the photo.

03

Tune the picture

Adjust brightness and contrast while you watch the Lit view, and add a frame if you want a stiffer panel.

04

Check it and download

Turn the model in 3D, then download the STL for your slicer.

How a lithophane works

A lithophane is a thin panel of translucent material whose thickness follows the picture. Where the photo is dark the panel is thick and little light gets through; where it is light the panel is thin and glows. Unlit it looks like a pale relief; held up to a lamp or a window, the photo appears.

This tool turns every point of your photo into a thickness between the thinnest and thickest values you set, white thinnest and black thickest, and builds a closed panel with a flat back. The STL is in millimeters; the format has no place to record a unit, and slicers read the numbers as millimeters.

Source: Library of Congress, STL (binary) format description.

Choosing a photo

Works best

Portraits, pets and close-ups with a clear subject, soft light and real shadows. Faces should fill a good part of the frame.

Needs help

Dark or flat photos: raise contrast in the Lit view, or brighten them a little.

Works poorly

Busy scenes with many small details, tiny faces in a group shot, and very small or blurry images.

Crop close to the subject before you start; the panel takes the shape of the photo. A small or soft photo can be sharpened with the AI image enhancer first.

Thickness, detail and file size

The thinnest point sets how bright the whites glow and the thickest how deep the blacks go. 0.8 and 3 mm are a common starting point for white PLA; very thin areas can break or print with holes, and very thick ones block nearly all light.

Detail sets how far apart the points are. Standard, every 0.2 mm, gives a 100 mm wide landscape photo about 190,000 points and an STL of about 19 MB; a square or upright photo of the same width makes a larger file. The size shows before you download, and a note appears when a file gets very large.

Printing and lighting

Use white or natural filament and print the panel solid, with 100% infill or enough walls to fill its whole thickness, so light passes evenly. Printed flat, each layer is one step of shade; printed standing up, the shading comes from the nozzle's sideways moves, which is why lithophanes are often printed upright.

Light it from behind with an even, diffuse light: a window, a lamp shade or an LED panel. A warm light gives the classic look.

Why use ImgTweak?

✓No upload, no account
✓Lit preview before printing
✓Thickness and detail you set
✓Watertight STL in millimeters
✓Frame, mirror and negative
✓Works on phones

For logos, signs and raised shapes instead of photos, use the image to STL converter.

Frequently asked questions

How do I make a lithophane from a photo?

Add the photo above, set the width and the thinnest and thickest points, adjust the picture in the Lit view, and download the STL. Print it in white filament and hold it up to a light. Nothing is uploaded.

What thickness should a lithophane be?

0.8 mm at the thinnest and 3 mm at the thickest is a common starting point for white PLA. Filaments let light through differently, so a small test print is the surest way to find yours. Thinner overall looks brighter; a bigger gap between the two gives more contrast.

What does the Lit view show?

An estimate of the panel with a light behind it, worked out from the thickness at every point: light fades the deeper it goes into the plastic. It is a good guide to the picture and contrast, but the real look depends on your filament and light.

Which detail setting should I use?

Standard, a point every 0.2 mm, suits most prints. Draft makes small files quickly; Fine puts a point every 0.1 mm, which makes files about four times larger for little visible gain on a 0.4 mm nozzle.

Should I mirror it?

The picture reads correctly from the textured side. If you will look at the flat back, with the texture facing the light, turn on Mirror so the picture isn't reversed.

What is Negative for?

It swaps light and dark, so light areas are thick. Use it for a special effect or to see the photo the other way round; for a normal lithophane leave it off.

Why add a frame?

A solid border at the full thickness makes the panel stiffer, gives you something to hold and helps it stand up. Its width is part of the width you set.

How should I print a lithophane?

Print it solid, with 100% infill or enough walls to fill the whole thickness, so light passes evenly. Printed flat, each layer is one step of shade: at 0.12 mm layers, 0.8 to 3 mm gives about 18 steps. Printed standing up, the shading comes from the nozzle's sideways moves instead, which is why lithophanes are often printed upright.

Can it make a curved or cylinder lithophane?

Not yet: this makes flat panels. A flat lithophane in a frame or a light box works well, and the STL can be bent into shape only with CAD software.

Is my photo uploaded?

No. The photo is read, the lithophane built and the STL written in your browser. Nothing is sent to a server, which matters for family photos.

Ready to make your lithophane?

Add a photo above, set the size and thickness, and download an STL for your printer.